Complete the Initial Setup Using the Nimble Setup Manager - NimbleOS 4.2 and Later
Before you begin
The Windows host that you use to initially configure the array must be connected to the same physical subnet as the array management port and have direct (non-routed) access to the array management port.
- Adobe Flash Player
- Nimble Windows Toolkit
Before you start, complete the Installation Checklist. You need the information from the checklist to perform the initial GUI setup.
The Nimble Setup Manager enables you to create a new group from an uninitialized array. The array is the only member of the group.
Procedure
- In the Windows Start menu, click .
-
Select one of the uninitialized arrays from the Nimble Setup
Manager list and click Next.
Note: If the array is not visible in Nimble Setup Manager, verify that the array is on the same subnet as the Windows host.
-
In the Information dialog, click OK.
Note: Clicking OK closes the Nimble Setup Manager, and continues the setup on the array through your web browser.
-
You may see a warning similar to There is
a problem with this website's security certificate. It is safe to
ignore this warning and click Continue.
If prompted, you can also download and accept the
certificate. Or create your own. Refer to the cert command in the Command
Reference. Note: If Internet Explorer 11 displays a blank page, clear the browser cache. The page should be visible after refreshing the browser.
- In the License Agreement, read the agreement, scroll to the bottom, check the acknowledgment box, and then click Proceed.
-
In the Array Setup, choose the appropriate group option and
click Next.
- Set up this array but do not join a group. Continue to the next step.
- Add this
array to an existing group. Enter the IP address of the group.
If you chose to join an existing group, your browser redirects to the login screen of the group leader array. Refer to the GUI Administration Guide or the CLI Administration Guide for steps on how to add an unconfigured array to a group, and complete the configuration.
-
Provide or change the following initial management settings,
then click Finish:
- Array name
- Group name
- Management IP address and subnet mask for the eth1 interface
- Default gateway IP address
- Domain name
- Administrator password
-
After a successful setup, click Continue.
Your browser automatically redirects to the Management
IP address of the array. Note: If the array does not initialize, check the cabling to the network switch and check the subnet mask.
- In the login screen, type the password you set and click Log In.
-
Provide the Subnet Configuration information for the following
sections, then click Next:
-
Management IP:
Note: The Management IP is used for the GUI, CLI, and replication. It resides on the management subnet and floats across all Mgmt Only and Mgmt + Data interfaces on that subnet.
- IP address
- Network
- Subnet mask
-
Subnet:
Note: All subnets subsequent to the management subnet must have the Data Only traffic type.
- Subnet label
- Network
- Netmask
- Traffic Type - Data only
- Traffic Assignment Note: This field is hidden if you are running a Fibre Channel array.
- Discovery IP Note: This field is hidden if you are running a Fibre Channel array.
- IP
Address Zone - Single, Bisect, or Even/Odd Note: This field is hidden if you are running a Fibre Channel array.
- Maximum Transmission Unit (MTU) – Standard, Jumbo, or Custom
- Frame
size in bytes – User specified value Ensure that your network switches support the selected frame size.Note: If Jumbo frames are selected, ensure that they are configured end to end. To confirm that Jumbo frames are supported, perform an end-to-end ping with the jumbo frame size and without fragmentation; for example: ping <hostname> -f -l 8972
The data port IP addresses are assigned to interface pairs, such as eth5 on controller A and eth5 on controller B. If one controller fails, the corresponding port on the remaining controller still has data access. At least one interface pair must be configured. However, a minimum of two is recommended.
Note: To add a data subnet, click Add Data Subnet and provide the required information.
-
Management IP:
-
Provide Interface Assignment information for the following
sections and click Next:
- Interface Assignment: For each IP interface, assign it a subnet and a Data IP address within the specified network. For inactive interfaces, assign the "None" subnet.
- FC Interface (Fibre Channel arrays only): This section displays the link status for all Fibre Channel ports. No configuration is required.
-
Diagnostic IP:
- Controller A diagnostic IP address within the specified network
- Controller B diagnostic IP address within the specified network
-
Provide the following Domain information and click Next:
- Domain Name
- IP address of your DNS server
You can list up to three DNS servers.
-
Provide the following Time information and click Next:
- Time (NTP) Server Type the hostname or IP address of your NTP server.
- Time Zone Choose the time zone the array is located in.
-
Provide Support information for the following sections and
click Finish.
-
Email Alerts
- From
Address
This is the email address used by the array when sending email alerts. It does not need to be a real email address, but it must be in the proper address format. Include the group or array name for easy identification.
- Send to Addresses
HPE Nimble Storage recommends that you check the Send event data to Nimble Storage Support check box.
- Simple Mail Transfer Protocol (SMTP) server hostname or IP address
- From
Address
- Diagnostic Analysis Checking the Send Diagnostic Analysis data to Nimble Storage Support check box enables HPE Nimble Storage Support to monitor your array, notify you of problems, and provide solutions.
-
HTTP Proxy
Diagnostic Analysis and software updates require an HTTPS connection to the Internet, either directly or through a proxy server. If a proxy server is required, check the Use HTTP Proxy check box and provide the following information to configure proxy server details:
- HTTP proxy server hostname or IP address
- HTTP proxy server port
- Proxy server user name
- Proxy server password
Note: The system does not test the validity of the SMTP server connection or the email addresses that you provided. -
Email Alerts
- Click Finish. A popup appears with status updates then the Setup Complete popup appears.
- Click Continue. The NimbleOS home page appears.
What to do next
Make sure that the Management IP address and the Controller Diagnostic IP addresses are added to your mail server's relay list.
Firewalls should not allow inbound communications from untrusted networks or any internet addresses.
- SSH: 2222 hogan.nimblestorage.com – For a Secure Tunnel connection to HPE Nimble Storage Support
- HTTPS: 443 nsdiag.nimblestorage.com – For Diagnostic Analysis and heartbeat
- HTTPS: 443 update.nimblestorage.com – For software updates
- HTTPS: 443 nsstats.nimblestorage.com – For relay of per-VM statistics (used in InfoSight VMvision)
Next, see After Installation and Initial Setup.